DVD writer problem

  Fruit Bat /\0/\ 19:18 05 Feb 2005

What does DVD +/- RW mean? particularly the + and - bit?

These are three different kinds of DVD disc
your player will work with all three.

+ / - disc are write once. Cannot be changed after burning data to them.

RW are write many times if using correct package writing software INCD from nero is one. You can use the DVD as if it were another Hard drive.


PIO is far too slow CD and DVD should be set to UltraDMA2

Re-enable DMA using the Registry Editor

Run REGEDIT. Go to the following key:

HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\{4D36E96A-E325-11CE-BFC1-08002BE10318}

It has subkeys like 0000, 0001, 0002, etc. Normally 0001 is the primary IDE channel, 0002 the secondary, but other numbers can occur under certain circumstances. Check the DriverDesc value to see which one it is.

Delete MasterIdDataChecksum or SlaveIdDataChecksum, depending on whether the device in question is attached as master or slave, but it can't actually hurt to delete both. Reboot. The drive DMA capabilities will be redetected.

Open Device Manager again and check whether the device is now actually using DMA mode. If so, congratulations, you've made it (at least until the next time Windows disables DMA).

Alternative Method—Uninstalling the Port
1. Uninstall the secondary IDE port
To do that, open Device Manager as follows. Right-click on My Computer, select Properties, click on the Hardware tag, click on the Device Manager button, click on the plus sign to the left of IDE ATA/ATAPI Controller, right-click on Secondary IDE Channel, click on Uninstall. Deactivating is not enough.

Reboot to make the changes active and permanent.

After booting Windows will automatically reinstall the IDE channel and the DVD (or CD) drive. This Plug-n-Play process can take a little while, so give it a minute after the boot process finishes.

2. Reactivate DMA
But this is not enough, because unfortunately Windows does not automatically activate DMA on a DVD or CD drive. You have to tell Windows to try to use DMA first.

For that, go to Device Manager again. Right-click on My Computer, select Properties, click on the Hardware tag, click on the Device Manager button, click on the plus sign to the left of IDE ATA/ATAPI Controller, double-click on the secondary IDE channel, click on Extended Settings and change the relevant setting from PIO only to DMA when available.

On Windows NT and 2000 you now have to reboot a second time, but Windows XP applies the change instantly. Then you can go to the same place in Device Manager again and check whether the device is now actually using DMA mode. If so, all is well.

Desensitize Your Computer's IDE Channels
There's a bit more to it. The following article offers a way to reduce the incidence of this problem, although it still doesn't solve it altogether.

IDE ATA and ATAPI Disks Use PIO Mode After Multiple Time-Out or CRC Errors Occur
click here

Do read this article because it contains a useful long-term workaround. But you have to go through the procedure described here to re-enable DMA first. Assuming you've done that, insert the ResetErrorCountersOnSuccess registry values mentioned in this article into both the primary and the secondary IDE port registry keys as described.

Unfortunately this is only a half solution, because when you enter an unreadable DVD, you will get 6 errors in a row, and the IDE channel will revert to PIO mode, but at least when you pull out the DVD in time and then insert a good one, the error counter will be reset and it will at least be a bit more difficult for Windows to hobble your IDE drive.

This thread is now locked and can not be replied to.

Elsewhere on IDG sites

Huawei Mate 20 Pro review: In-depth hands-on

Adobe's groundbreaking prototypes of new features and apps for Creative Cloud

iPhone XR release date, price & specs

Test : le Samsung Galaxy A9