Samsung Galaxy A8 review: Hands-on
please could you help. when i start my computer up it goes to the safe mode/ start windows normally screen. whichever option i pick it goes to the loading up windows screen and then restarts and starts the process again. please help!!!
Best to only post in one forum, Laura.
Try safe mode.[just keep tapping F8 as the computer starts.]If it works try last good configuration or system restore.
Repair XP by install over the top of existing system
1. Boot the computer using the XP CD. You may need to change the boot order in the system BIOS so the CD boots before the hard drive. Check your system documentation for steps to access the BIOS and change the boot order.
2. When you see the "Welcome To Setup" screen, you will see This portion of the Setup program prepares Microsoft Windows XP to run on your computer:
To setup Windows XP now, press ENTER.
To repair a Windows XP installation using Recovery Console, press R.
To quit Setup without installing Windows XP, press F3.
3. Press Enter to start the Windows Setup.
To setup Windows XP now and Repair Install , press ENTER.
DO NOT choose "To repair a Windows XP installation using the Recovery Console, press R", (you Do Not want to load Recovery Console).
4. Accept the License Agreement and Windows will search for existing Windows installations.
5. Select the XP installation you want to repair from the list and press R to start the repair.
6. Setup will copy the necessary files to the hard drive and reboot.
Do not press any key to boot from CD when the message appears.
Setup will continue as if it were doing a clean install, but your applications and settings will remain intact.
How you access the repair options will depend upon whether you have a Windows Vista installation disk or whether your operating system came pre-installed by your PC manufacturer.
Windows Installation Disk
With the Complete PC Restore Option you must have made a backup of your system, either on your hard drive or on a set of DVDs, in order to use this option. If you don't have a backup then don't use this option
1/ make sure your PC can boot directly from the Vista DVD. Obviously, most modern PCs can. With older machines you may need to check the PC's BIOS
2/ Start the PC
3/ Immediately insert the Windows Vista DVD into the DVD drive
4/ A Black screen will appear with the words 'Press any key to boot from CD or DVD'
5/ Press Any key to start the booting process
6/ A new screen will now appear with a progress bar. The legend say's 'Windows is loading files'
7/ After a few minutes the Microsoft copyright window ill appear and another small progress bar will be visible
8/ You will next see a Blue curtained screen
9/ After a short while the Language option screen will appear
10/ Select your language and keyboard language and the Click the Next button
11/ At the bottom left of the next screen - the Install screen, Click on the Repair Your Computer option
12/ The System recovery options will now search for your Windows Vista installation
13/ Once the Vista installation has been located, Highlight it and then Click the Next button
14/ You are now presented with the following set of recovery options
* Startup repair - This automatically fixes problems that are preventing Windows from starting
* System Restore - This will Restore Windows to an earlier point in time
* Windows Complete PC Restore - This will completely restore your entire PC - programs, system settings and files - from a back up that you have previously created (Available in Windows Vista Business, Enterprise and Ultimate editions only)
* Windows Memory Diagnostic Tool - This checks your computer's memory hardware for errors
* Command Prompt - This opens a Command Window
15/ Click on the Option you require and follow the onscreen prompts
If no repair options are available your PC manufacturer may have replaced the tools or customised them. Check your Computer Manual before proceeding.
1/ Start your PC
2/ If your PC has one operating system Press and Hold the F8 key as your PC starts. If the Windows Logo appear you will need to start again
3/ If you have a dual boot system a Boot option menu will appear. Highlight the Vista operating system and Press the F8 key
4/ In both cases, if all has gone well, an Advanced options screen will now appear
5/ Highlight the repair Your Computer option and Press Enter
6/ Select a keyboard layout, and then Click the Next button
7/ Next select your user Name and Enter your Password, then Click OK
8/ The recovery options should now appear
This thread is now locked and can not be replied to.