UDMA & POI

  marsman 12:39 23 Mar 2007
Locked

I cant get my PC to accept UDMA mode, its stuck on POI,ive tried the Microsoft solution, Ive un-intalled the driver and let windows re-install. Could it be the cable, is it easy to tell an 40 pin to an 80 pin cable? Any idea's?

  hkvic 12:48 23 Mar 2007

Try this solution click here

  Stuartli 13:28 23 Mar 2007

Uninstall the Secondary IDE Channel in Device Manager and reboot - usually cures it.

  Stuartli 13:30 23 Mar 2007

This also applies to the Primary channel (you don't state which components are affected).

  marsman 14:21 23 Mar 2007

Cheers Stuart,

Im going to pick a new 80 pin cable up to rule that out. It came to my attention because the PC seems to take too long to start up, so I started checking the hard drive, when I found it shoudnt be set to POI, I tried to change it, but it woudnt let me. I have only un-installed the primary IDE, are you suggesting I should un-install both (secondary) as well? Whe I reboot it still shows POI, with no option to change to DMA.

  skidzy 14:24 23 Mar 2007

May help click here

  marsman 17:05 23 Mar 2007

Ok, installed new cable, but still no UDMA option?

  Fruit Bat /\0/\ 17:52 23 Mar 2007

Re-enable DMA using the Registry Editor

Run REGEDIT. Go to the following key:

HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\{4D36E96A-E325-11CE-BFC1-08002BE10318}

It has subkeys like 0000, 0001, 0002, etc. Normally 0001 is the primary IDE channel, 0002 the secondary, but other numbers can occur under certain circumstances. Check the DriverDesc value to see which one it is.

Delete MasterIdDataChecksum or SlaveIdDataChecksum, depending on whether the device in question is attached as master or slave, but it can't actually hurt to delete both. Reboot. The drive DMA capabilities will be redetected.

Open Device Manager again and check whether the device is now actually using DMA mode. If so, congratulations, you've made it (at least until the next time Windows disables DMA).

Alternative Method—Uninstalling the Port
1. Uninstall the secondary IDE port
To do that, open Device Manager as follows. Right-click on My Computer, select Properties, click on the Hardware tag, click on the Device Manager button, click on the plus sign to the left of IDE ATA/ATAPI Controller, right-click on Secondary IDE Channel, click on Uninstall. Deactivating is not enough.

Reboot to make the changes active and permanent.

After booting Windows will automatically reinstall the IDE channel and the DVD (or CD) drive. This Plug-n-Play process can take a little while, so give it a minute after the boot process finishes.

2. Reactivate DMA
But this is not enough, because unfortunately Windows does not automatically activate DMA on a DVD or CD drive. You have to tell Windows to try to use DMA first.

For that, go to Device Manager again. Right-click on My Computer, select Properties, click on the Hardware tag, click on the Device Manager button, click on the plus sign to the left of IDE ATA/ATAPI Controller, double-click on the secondary IDE channel, click on Extended Settings and change the relevant setting from PIO only to DMA when available.

On Windows NT and 2000 you now have to reboot a second time, but Windows XP applies the change instantly. Then you can go to the same place in Device Manager again and check whether the device is now actually using DMA mode. If so, all is well.

3. Driver is not intended for this platform
If you keep getting the following error message:

There is a problem installing this hardware.

IDE channel

An error occurred during the installation of the device. Driver is not intended for this platform.

then the way out is to rename C:\WINDOWS\system32\drivers\atapi.sys (or a similar path on your computer) to something like atapi.old.

If that's not possible, you can try it from the repair console (boot from the Windows install CD and select the repair console).

If Windows always automatically recreates atapi.sys, you can try renaming it in safe mode or from a command line window or you can try to rename or remove it in the driver cache as well.

Desensitize Your Computer's IDE Channels
There's a bit more to it. The following article offers a way to reduce the incidence of this problem, although it still doesn't solve it altogether.

IDE ATA and ATAPI Disks Use PIO Mode After Multiple Time-Out or CRC Errors Occur
click here

Do read this article because it contains a useful long-term workaround. But you have to go through the procedure described here to re-enable DMA first. Assuming you've done that, insert the ResetErrorCountersOnSuccess registry values mentioned in this article into both the primary and the secondary IDE port registry keys as described.

Unfortunately this is only a half solution, because when you enter an unreadable DVD, you will get 6 errors in a row, and the IDE channel will revert to PIO mode, but at least when you pull out the DVD in time and then insert a good one, the error counter will be reset and it will at least be a bit more difficult for Windows to hobble your IDE drive.

  marsman 18:58 23 Mar 2007

ta fruit, i read that somewher no success.

This thread is now locked and can not be replied to.

Elsewhere on IDG sites

Best phone camera 2017

Stunning new film posters by Hattie Stewart, Joe Cruz & more

iPad Pro 10.5in (2017) review

28 astuces pour profiter au mieux de votre iPhone